Bonding to Wood based Sub-floors
Jun 10, 2009 DIY tips, bonding, how to, wood flooring
Wood-based sub-floors are materials such as floorboards, flooring grade chipboard, plywood, or OSB.
Existing hardwood floor coverings should be removed before installation of new hardwood floors.
Environmental Conditions
- All wet trades must be thoroughly dry before flooring materials are delivered to site.
- Maintain suitable ambient humidity 40 to 60% RH. (Monitor with a hygrometer)
- If necessary employ a domestic humidifier / dehumidifier to maintain suitable conditions.
Moisture condition of Wood based sub-floors
- Ensure that wood based sub-floor materials are not > 2% higher in moisture than the new wood flooring materials being installed.
Suspended wood based sub-floors at ground level
- Voids beneath suspended wood based sub-floor on ground level must be well ventilated to avoid high humidity in the sub-floor void.
- First lay a building paper moisture barrier (e.g. Sisalkraft Moistop), over the existing sub-floor overlapping joins by 100mm and taping with a waterproof tape.
- Then install a WBP ply layer, securely fixing through the building paper to the sub-floor.
Soundness of sub-floors
- Ensure all sub-floors are sound, of load-bearing strength and free from contaminants that may impede adhesion. (Note: If sub-floors are contaminated or affected by adhesive residues seek further advice).
Evenness of sub-floor
- In order to achieve satisfactory contact between wood flooring and adhesive, sub-floors must be even to within 2mm over any 2 lineal meter area.
- Floor boarded sub-floors typically require a WBP plywood covering to be securely fastened to the floorboards before adhesive fixing new wood flooring.
- It is recommended that flooring grade chipboard, OSB & old floorboards are first covered with WBP plywood which is securely fastened to the sub-floor before adhesive fixing new wood flooring to protect against surface contaminants that may impede adhesion.
Adhesive bonding of wood flooring to wood based sub-floor
- Use a purpose made, permanently flexible adhesive such as 1-part polyurethane, when adhesive fixing.
- Always use the trowel type recommended by the adhesive manufacturer for the type of flooring being installed (e.g. solid plank, strip, woodblock, engineered plank etc).
- Replace worn trowels.
- Ensure full contact between the underside of the flooring element and adhesive.
- Any adhesive that that comes into contact with the face of the boards must be cleaned off whilst wet, as residues are not removable when cured.
Provision for expansion
- As a guide only allow a minimum 15mm expansion wherever the floor meets obstacles including perimeters walls, structural supports, hearths etc.
- Create additional expansion breaks in doorways using suitable profiles such as T-section thresholds or transition strips.
- Create additional expansion breaks in large floors.
- Where possible install flooring so that planks, strips run parallel to the longest walls, so the direction of greatest potential expansion (i.e. across the grain) does not coincide with the direction of greatest dimension, esp. in large floors.
- The precise combined provision for expansion must be judged by the installer taking into account environmental humidity, moisture content of wood at time of installation, timber specie and size of the floor.
You can contact us for more information at www.floorcraft.uk.com or call us on 01252 372227/07970 491384 ask for Gavin Winder (we are based in Farnborough, Hampshire, UK and stock all of the above mentioned wood flooring adhesives, latex, underlays etc).
Tags: adhesives, Bona, bonding, DIY guide, Duralay, latex, Sika, underlays, wood flooring
How to Bond a Wood Floor
Jun 10, 2009 DIY tips, bonding, how to, wood flooring
Both solid & engineered wood flooring can be bonded to a variety of sub-floors using purpose made adhesives, creating a traditional solid feel underfoot.
Environmental Conditions
- All wet trades must be thoroughly dry before flooring materials are delivered to site.
- Maintain suitable ambient humidity 40 to 60% RH. (Monitor with a hygrometer)
- If necessary employ a domestic humidifier / dehumidifier to maintain suitable conditions.
Moisture condition of mineral based sub-floors
- Ensure that screeds, concrete, etc are less than 60% Relative humidity before installation commences.
- Employ a suitable primer moisture barrier if necessary, we recommend Bona R410 or Sika MB.
- At ground floor level and below, wood flooring must be protected from ground water by an integral DPM.
We recommend Duralay Excel or Duralay Silent Gold or in the case of basements by tanking, however due to moisture levels normally being particularly high in basements we would not recommend the use of solid wood flooring.
Soundness of sub-floors
- Ensure all sub-floors are sound, of load-bearing strength and free from contaminants that may impede adhesion. (Note: If sub-floors are contaminated or affected by adhesive residues seek further advice).
- Check that the sub-floor has a satisfactory cohesive strength before adhering wood flooring. i.e that it is not breaking up or loose
- Avoid accelerated drying of new concrete/screeds as this may lead to poor cohesive strength and may also cause the screed/slab to slump
Evenness of sub-floor
- In order to achieve satisfactory contact between wood flooring and adhesive, sub-floors must be even to within 2mm over any 2 lineal meter area.
- If levelling is required above a suitable primer moisture barrier, apply a purpose-made fine graded aggregate over the second coat of wet primer, allow to cure then vacuum off all loose aggregate; (This will aid adhesion between primer and levelling compound). Then use ‘rapid dry formulae’ water-mix (i.e. instead of latex mix) levelling compound, as these are typically stronger and develop strength quicker, we Recommend Dunlop or Aritex Yellow bag and bottle
- Ensure that levelling compounds are fully cured and thoroughly dried in favourable drying conditions before installation commences
Adhesive bonding of wood flooring to sub-floor
- Use a purpose made, permanently flexible adhesive such as 1-part polyurethane, when adhesive fixing, we recommend Bona R850 or Sika T54
- Apply adhesive to the sub-floor not the wood flooring or the tongue and groove.
- Always use the trowel type recommended by the adhesive manufacturer for the type of flooring being installed (e.g. solid plank, strip, woodblock, engineered plank etc).
- Replace worn trowels.
- Ensure full contact between the underside of the flooring element and adhesive.
- Any adhesive that that comes into contact with the face of the boards must be cleaned off whilst wet, as residues are not removable when cured.
IMPORTANT NOTE
Always check the mutual compatibility of moisture barriers, primers, aggregates, levelling compounds and adhesives before installation. Refer to instructions for use for each product.
Provision for expansion
- As a guide only allow a minimum 10mm expansion wherever the floor meets obstacles including perimeters walls, structural supports, hearths etc.
- Create additional expansion breaks in doorways using suitable profiles such as T-section thresholds or transition strips.
- Create additional expansion breaks in large floors.
- Where possible install flooring so that planks, strips run parallel to the longest walls, so the direction of greatest potential expansion (i.e. across the grain) does not coincide with the direction of greatest dimension, esp. in large floors.
- The precise combined provision for expansion must be judged by the installer taking into account environmental humidity, moisture content of wood at time of installation, timber specie and size of the floor.
Tip
- Flooring must not be exposed to artificial heat sources from the sub-floor. Hot water pipes within screeds can cause excess heat and must be thoroughly insulated. Floor temperatures must not exceed 24 Celsius.
You can contact us for more information at www.floorcraft.uk.com or call us on 01252 372227/07970 491384 ask for Gavin Winder (we are based in Farnborough and stock all of the above mentioned adhesives, latex, underlays etc).
Tags: adhesives, Bona, bonding, concrete, DIY, Duralay, flooring, glues, latex, screeds, Sika, underlays, wood
